A John Deere certified technician will inspect your machine in a shop in one of our 28 locations and make sure your equipment is ready to run when you are.
All inspections include a detailed estimate of recommended repairs.
Equipment Inspections
compact construction 500 Hour Service
$419.99*Plus parts
Skid steer, compact track loader, and compact excavator service
Certified Technicians Will:
- Drain and refill engine oil and filter
- Replace primary and final fuel filter
- Replace hydraulic filter
- Replace primary and secondary air filters
- Replace cab filters (if equipped)
- Replace hydraulic reservoir breather (if equipped)
- Check:
- Travel gear case oil
- Coolant level
- Bucket teeth (if equipped)
- Track tension
- Fan belt tension
- Lubricate all points, including boom, cylinder, QuickTatch, swing bearing, bucket, and link pins
- Free inspection with 500-hour service!
Sprayer Inspection
$699 $599*
PLUS 20% off parts purchased as result of inspection**
Certified Technicians Will:
- Record & clear diagnostic codes
- Inspect engine, fuel system, chassis, boom solution system & foam marker system.
- Includes detailed estimate of needed repairs
Be sure to ask about deferred payment* financing options for service with a John Deere Financial Multi-useTM Account!
Planter Inspection
$699 $599*
PLUS 20% off parts purchased as result of inspection**
Certified Technicians will:
- Check vacuum doors and seals
- Check seed meter brushes
- Check Tru Vee opener blade wear and bearings
- Check closing wheel alignment
- Check scraper wear
- Check air bags for pneumatic down force (if equipped)
- Check seed tube wear
- Check seed tube guard wear
- Check down force springs (if equipped)
- Check parallel arm bushings
Seed Meter Testing – $25 Per Row
Ensure the correct rate is planted regardless of seed shape or size. Includes a row-by-row printout of population, skips, doubles, and singulation. Contact your Precision Ag Consultant or call the TriGreen Connected Support Center at (888) 399-7448 to schedule. $25 per row plus applicable parts and labor charges for repairs.
Picker Inspection
$1,199 $899*
PLUS 20% off parts purchased as result of inspection**
Certified Technicians will:
- Inspect picker unit moistener system
- Check all fluid levels
- Check hydraulic system for leaks
- Check augers and bearings
- Check feeder belt, belt motor, and drive coupler
- Check meter and beater rollers
- Inspect round module builder belts
- Inspect chain drive
- Inspect wrap drive belts
- Inspect wrap clutch
- Check moistener system operation
- Check air system operation
- Inspect row unit cabinet
Combine Inspection
$799*
PLUS 20% off parts purchased as result of inspection**
Certified Technicians will:
- Inspect the cab
- Record and clear all stored codes
- Inspect feederhouse area
- Inspect separator area
- Inspect the threshing area
- Inspect power train
- Inspect all belts
- Inspect for bearing failures
- Inspect electronics/displays
- Inspect the grain handling/grain tank area
- Inspect the engine/engine compartment area
Header Inspection
$299 $199*
PLUS 20% off parts purchased as result of inspection**
Certified Technicians will:
- Adjust platform auger & floor strippers
- Adjust knife, hold downs and guards
- Calibrate corn head or platform to combine if participating in combine inspection program
- Check & top off oil in platform gear box and corn head row units.
- Check & adjust corn head auger flighting clearance
- Includes a detailed estimate of needed repairs
Ask about no payment/no interest options on service with a John Deere Financial Multi-Use AccountTM.
Baler Inspection
$419.00*
PLUS 20% off parts purchased as result of inspection**
Certified Technicians will:
- Adjust and lube chains
- Grease all fittings
- Align and adjust chain idlers
- Add fluid to main gear case
- Check for missing pick up teeth and strippers
- Inspect cam and cam bearings
- Check twine arm adjustment
- Inspect net wrap steel rolls for pits or rust
- Inspect chains and sprockets for wear
- Inspect all roller shafts and bearings
- Operate baler and check bearings with a heat gun
- Inspect baler belts, lacing, and pins
- Inspect hydraulic cylinders and hoses for leaks
- Inspect monitor operation and adjust any sensors if needed
*Offer expires February 28, 2026. Inspection must be scheduled by February 28, 2026 to qualify for discounts. Exclusions may apply. Environmental fees and taxes are at an additional cost. Attachment and implement service is not included. Repairs are at an additional cost to the maintenance and inspection. No warranty is implied or stated. Prices in U.S. dollars.
*Price does not include parts, machine transport or technician travel for field inspection. Travel charges will be quoted upon service scheduling
**Equipment-specific parts percent off offer includes discounts off eligible parts recommended as a result of the inspection, service or seed meter testing. No maximum discount.
Cannot be combined with other offers. Some exclusions may apply. Parts must be purchased and in-shop work must be performed by February 28, 2026 to receive the discount.